Hydravex
2020 Hydravex HX-2040 Waterjet Cutting System
- Year
- 2020
- Model
- HX-2040
- Location
- Calgary, AB
- Condition
- Good
$115,000 CAD
Or call 905-555-0142
Photos
2020 Hydravex HX-2040 Waterjet Cutting System — Photo Gallery
About This Listing
Equipment Details
A 2020 Hydravex HX-2040 waterjet cutting system, taken in on trade at our Calgary branch from a fabricator upgrading to a 5-axis waterjet. This 60,000 psi pump, 2 x 4 m table configuration cuts metal, stone and composite alike without a heat-affected zone, and it has stayed in daily production on one site since new. Our service team completed the scheduled 3,000-hour pump seal and intensifier rebuild before putting it on the used floor. We can arrange rigging, plumbing and a start-up cut sample anywhere in Western Canada.
Traded in by a Calgary metal and stone fabricator upgrading to a 5-axis waterjet. Pump seals and intensifier rebuilt at 3,000-hour service interval before listing; catcher tank and garnet removal system cleaned and tested. Cutting head shows normal wear from garnet abrasive use.
Highlights
Key Features
- 60,000 psi direct-drive intensifier pump
- Bulk garnet hopper with metered delivery
- Catcher tank with automated garnet removal
- No heat-affected zone — cuts metal, stone and composites
- Dual-tray shuttle table for continuous loading
- Remote diagnostics port for service calls
Specifications
2020 Hydravex HX-2040 Waterjet Cutting System Technical Specs
- Table size
- 2000 x 4000 mm (79" x 157")
- Pump pressure
- 60,000 psi (414 MPa)
- Pump type
- Direct-drive intensifier
- Cutting head
- 5-axis-ready, fixed on this unit
- Positioning accuracy
- ± 0.05 mm (0.002")
- Maximum cutting speed
- 45 m/min (1,772 in/min) rapid
- Garnet system
- Bulk hopper with metered delivery
- Control
- Hydravex HC-Flow touchscreen
- Recorded pump hours
- 6,800 hrs
| Table size | 2000 x 4000 mm (79" x 157") |
| Pump pressure | 60,000 psi (414 MPa) |
| Pump type | Direct-drive intensifier |
| Cutting head | 5-axis-ready, fixed on this unit |
| Positioning accuracy | ± 0.05 mm (0.002") |
| Maximum cutting speed | 45 m/min (1,772 in/min) rapid |
| Garnet system | Bulk hopper with metered delivery |
| Control | Hydravex HC-Flow touchscreen |
| Recorded pump hours | 6,800 hrs |
What's Included
Equipment Package
Included
- Delivery within Alberta, FOB truck
- Installation, plumbing and start-up cut sample
- Operator training on site
- 90-day parts and labour warranty
Not Included
- Freight outside Alberta
- Garnet abrasive supply
- Water treatment system upgrade
- Taxes
Interested?
Ready to move forward?
Speak with our team about the 2020 Hydravex HX-2040 Waterjet Cutting System. We'll provide full details, inspection history, and delivery options.
New Equipment
Also from Hydravex
Browse our current new Hydravex lineup alongside this used listing.
Waterjet cutting system
Hydravex HX-2040
The HX-2040 is Hydravex's straight-head waterjet, built for shops that need clean, cold-cut edges on metal, stone, glass, rubber and composites without the cost of a 5-axis head. A 60,000 psi direct-drive intensifier pump feeds a single vertical cutting head over a 2000 x 4000 mm (6.5' x 13') tank bed, cutting material up to 100 mm (4") thick with no heat-affected zone. The Hydravex FlowLogic control drives nesting and pierce sequencing, and an automatic abrasive metering system keeps garnet consumption consistent from part to part. Tollaston runs a test cut on your own material, sets up the abrasive and water supply, and trains your team on programming.
5-axis waterjet cutting system
Hydravex HX5-3060 5-Axis
The HX5-3060 5-Axis adds an articulating wrist to Hydravex's waterjet platform, so the cutting head tilts through the kerf and cancels the natural taper a straight jet leaves on thicker material — square edges on parts that would otherwise need a secondary finishing pass. A 90,000 psi direct-drive intensifier pump feeds a single head over a 3000 x 6000 mm (10' x 20') tank bed, cutting metal, stone, glass, tile and composites with the same setup. Because it cuts stone as cleanly as metal, Tollaston also lists this machine under Stone CNC Centres for stone fabricators. The Hydravex FlowLogic control manages taper compensation automatically from the part's material and thickness. Tollaston runs a test cut on your own material, sets up abrasive supply, and trains your programmers.