Ferroniq
2022 Ferroniq FE-135 Servo Press Brake
- Year
- 2022
- Model
- FE-135 Servo
- Location
- Vaughan, ON
- Condition
- Excellent
Contact for pricing
This unit is currently reserved. You're welcome to inquire in case it becomes available.
Or call 905-555-0142
Photos
2022 Ferroniq FE-135 Servo Press Brake — Photo Gallery
About This Listing
Equipment Details
A 2022 Ferroniq FE-135 servo-electric press brake, taken in on trade at our Vaughan Tech Centre from a fabricator downsizing its bending line. This is the 135-ton, 3.2 m (10.5') bed configuration most sheet metal shops run for structural and enclosure work, and it carries genuinely low hours for its age. Our Tech Centre technicians ran the full servo drive and CNC back gauge through a diagnostic cycle and re-certified the safety light curtain before listing it. Currently reserved for a customer completing financing; contact us to be notified if it becomes available again.
Low-hour trade-in from a Vaughan-area fabricator that downsized its bending line. Servo-electric drive and back gauge tested through full travel with no fault codes; ram parallelism within 0.02 mm across the bed. Tooling clamps and safety light curtain re-certified before listing.
Highlights
Key Features
- Servo-electric dual-cylinder drive
- 2-axis CNC back gauge
- Offline programming with 3D bend simulation
- AKAS-type laser safety guarding
- Crowning table for long, thin parts
- Quick-change tooling clamps
Specifications
2022 Ferroniq FE-135 Servo Press Brake Technical Specs
- Bending force
- 135 tons (1,200 kN)
- Bed length
- 3200 mm (10.5')
- Daylight opening
- 500 mm (19.7")
- Stroke
- 300 mm (11.8")
- Drive
- Servo-electric, dual-cylinder
- Back gauge
- CNC, 2-axis (X, R)
- Control
- Ferroniq FC-7 touchscreen with offline programming
- Repeatability
- ± 0.01 mm (0.0004")
- Recorded cycle count
- 18,400 cycles
| Bending force | 135 tons (1,200 kN) |
| Bed length | 3200 mm (10.5') |
| Daylight opening | 500 mm (19.7") |
| Stroke | 300 mm (11.8") |
| Drive | Servo-electric, dual-cylinder |
| Back gauge | CNC, 2-axis (X, R) |
| Control | Ferroniq FC-7 touchscreen with offline programming |
| Repeatability | ± 0.01 mm (0.0004") |
| Recorded cycle count | 18,400 cycles |
What's Included
Equipment Package
Included
- Delivery within the GTA, FOB truck
- Installation and levelling on site
- Operator training (half day)
- 6-month parts warranty
Not Included
- Tooling beyond the standard punch and die set supplied
- Freight outside the GTA
- Backgauge fingers upgrade
- Taxes
Interested?
This unit is reserved — inquire anyway
This unit may still become available. Submit an inquiry and we'll keep you posted.
New Equipment
Also from Ferroniq
Browse our current new Ferroniq lineup alongside this used listing.
Servo-electric press brake
Ferroniq FE-135 Servo
The FE-135 Servo replaces a hydraulic power pack with a servo-electric drive, so it draws power only during the bend itself, runs noticeably quieter, and needs no hydraulic oil to maintain. Rated at 135 US tons over a 3000 mm (10') bending length, it holds bend-to-bend repeatability tighter than a comparable hydraulic brake and starts up ready to bend with no oil warm-up cycle. A 4-axis CNC back gauge and the Ferroniq Arc 19 touchscreen control handle multi-bend part programs from a graphical sequence editor. Tollaston sets up and levels the brake, programs your first parts, and trains your operators on tooling and bend-sequence setup.
Hydraulic press brake
Ferroniq FH-320 Tandem
The FH-320 Tandem is Ferroniq's heavy hydraulic press brake, rated at 320 US tons over a 6000 mm (20') bending length and built from the ground up to synchronize with a second FH-320 for tandem bends beyond any single brake's length. Twin synchronized hydraulic cylinders and a 6-axis CNC back gauge (X, R, Z1, Z2, X1, X2) hold position across the full bed, and automatic CNC crowning keeps the bend angle consistent end to end even on thin material. The Ferroniq Arc 19 touchscreen control programs bend sequences and tandem synchronization from one screen. Tollaston installs and levels the brake, runs a test bend on your own material, and trains your operators on tandem setup and tooling changeover.
CNC panel folder
Ferroniq FP-2500 Panel
The FP-2500 Panel automates the up-and-down bending that would otherwise take a press brake and a second set of hands. A blade-and-beam bending head folds sheet up to 2500 x 1250 mm (98" x 49") and 3 mm (0.12") mild steel — 2.5 mm (0.1") stainless — while the sheet stays flat on the table, so one operator loads and programs box, tray and enclosure parts with every bend angle and sequence stored as a part program. The Ferroniq Arc 19 touchscreen control calls up to 200 stored programs and drives the motorized back gauge and blade positioning automatically between bends. Tollaston installs, programs your first parts library, and trains your team on the workflow.